Filter
ID :  till 
Mnemonic code:
Code in external DB source:
Name:
Tags:
Sorting:  till 
Preview text:
Detailed description:
Activity Start Date: Select date in calendarSelect date in calendar
Activity End Date: Select date in calendarSelect date in calendar
Number of shows:  till 
Information Block type:
Information Block ID:
Information Block mnemonic code:
Information Block name:
Information Block code in external DB source:
Create date: Select date in calendarSelect date in calendar
Описание:
Теги:
Автор:
Рубрика:
  

Journal

The design of rubber lining for raw material and cement mills, produced by OAO UrRTI is discussed. The advantages of using rubber and rubber magnetic ...
Issue №3, 2011
Section: Equipment and technology
Keywords: rubber lining, rubber-magnetic lining, lifter
Autor: V.G. Maslennikov, A.Y. Stikhin.
The article describes the experience of improving the equipment for cement production, in particular, ball mill thrust bearings, based on the achievem...
Issue №3, 2011
Section: Equipment and technology
Keywords: mechatronics, control, hydraulic system, ball mill, bearing
Autor: P.S. Zbožinek, O. Ožana.
The article discusses the use of various alternative fuels, their properties, as well as the negative impact of fuel on the refractory lining, anchor ...
Issue №3, 2011
Section: Refractories
Keywords: alternative fuel, refractory lining, silicon carbide, zirconium dioxide
Autor: V. Bolimov, A. Klemba.
The influence of water-to-cement mass ratio (w/c) on early-age properties of cement-based materials is investigated using a variety of experim...
Issue №3, 2011
Section: Science and production
Keywords: compressive strength, hydration, water-to-cement mass ratio, calorimetry, crack formation
Autor: D.P. Bentz, M.A. Peltz, J. Winpigler.
The article addresses the problem of energy efficiency through combining low-melting mixes of raw materials and commercial development of cement produ...
Issue №3, 2011
Section: Science and production
Keywords: non-traditional raw materials, volcanic glass, kiln performance increase, hydraulic activity
Autor: Z.P. Pulatov, E.M. Butayev.
The paper summarizes the data on streamlining the technological parameters of production and commercial output of moderate heat of hydration Portland ...
Issue №3, 2011
Section: Special binders
Keywords: Portland cement, hydraulic facilities, heat generation
Autor: L.A. Vertoprakhova, I.A. Solovieva, V.E. Klimov, V.P. Skakun, V.A. Afanasin.
In the second part of the article on the optimization of combustion using the aerodynamic simulation a case study of substitution of natural gas with ...
Issue №3, 2011
Section: Waste utilization
Keywords: AFR, aerodynamics, simulation, kiln, calciner
Autor: T. Abbas, T. Lowes.
The paper examines the effect of galvanic sludge produced in the treatment of aluminium products on the hardening of cement compositions. It was found...
Issue №3, 2011
Section: Waste utilization
Keywords: galvanic sludge, additives, structure, cement stone, setting deadlines, contraction, cement strength
Autor: V.G. Khozin, N.M. Morozov, S.V. Stepanov.
The potential of slag Portland cement with high (50%) content of granulated blast furnace slag to prevent negative consequences for the qu...
Issue №3, 2011
Section: Concrete
Keywords: concrete corrosion, slag Portland cement, blast-furnace slag
Autor: G.S. Royak, I.V. Granovskaya.
Deformation and destruction of concrete samples during freezing in de-icing solutions were studied. Dilatometric examination can identify the behaviou...
Issue №3, 2011
Section: Concrete
Keywords: causes of distraction, rest deformation, cyclic freezing – thawing, concrete
Autor: B.Ya. Trofimov, S.P. Gorbunov.

1, ... 170, 171, 172, 173, 174, ... 220
The use of materials published on the site is allowed only with reference to the source (the journal «Cement and its application») and a hyperlink to the quoted material.
© 2007-2024 PetroCem Ltd
Privacy policy