Journal
This article addresses the problem of ensuring the geometric stability of concrete elements in industrial and mechanical engineering structures exp...
| Issue №3, 2026 |
| Section: Science and production |
| Keywords: structural materials, high-performance concrete, thermal expansion, expansive additive, dimensional stability, machine tool beds, shrinkage deformations, thermal expansion, hydrophobic coatings, freezethaw cycling, dynamic properties, damping properties, industrial equipment |
| Autor: V.A. Beregovoy, I.Y. Lavrov, A.V. Semiletkov. |
The article discusses innovative technologies developed by the Russian company OOO NPO BETOHIMIKS in the field of sol modification of concrete. Nan...
| Issue №2, 2026 |
| Section: Equipment and technology |
| Keywords: concrete, sol, colloid, sol modifier, nanotechnology, mineral additive |
| Autor: V.E. Khovansky. |
The rheological properties of concrete mixtures are crucial for additive construction technologies. Methods for ensuring the required properties va...
| Issue №1, 2026 |
| Section: Concrete |
| Keywords: 3D printing with concrete, additive technologies, rheological properties, viscosity, thixotropy, initial shear stress, plasticity, extensibility, elongation at break, redispersible polymer powders, cellulose esters, polypropylene fiber, rotary rheometer. |
| Autor: A.M. Kharitonov, N.N. Shangina, E.V. Malaschenko. |
This study examines the effect of mineral additives, wollastonite and diopside, on the aggregation stability of a foamed concrete mixture obtained ...
| Issue №4, 2025 |
| Section: Science and production |
| Keywords: cement-ash binder, foam concrete, wollastonite, diopside, mineral additives, fly ash |
| Autor: E.A. Bartenyeva, L.V. Ilyina, N.S. Vishnyakov. |
Robotization of construction through the use of additive technologies is one of the most promising areas for increasing labor efficiency in the con...
| Issue №3, 2025 |
| Section: Concrete |
| Keywords: additive fabrication, 3D printing, expanded polystyrene concrete |
| Autor: V.V. Molodin. |
The paper presents the results of determination of activity of diabase-porphyritic rock fines (DPF), which is formed during grading of crushed sto...
| Issue №5, 2024 |
| Section: Waste utilization |
| Keywords: activity, criterion, diabase, porphyrite, screening, fraction, additive, strength, mineral, Portland cement, frost resistance |
| Autor: J.B. Nazhimov, A.M. Khozhabaev, H.L. Usmanov, Z.R. Kadyrova. |
The paper deals with the problems of compatibility of cement with organic modifiers of rheological properties of cement dough as estimated by the ...
| Issue №4, 2024 |
| Section: Science and production |
| Keywords: compatibility of cement with additives, rheological characteristics, cement paste, mortar mix, Kantro test, mini-cone |
| Autor: L.D. Shakhova. |
Subject of the research presented in the article is the possibility of creating a technology for light-transmitting concrete products by layer-by-...
| Issue №4, 2024 |
| Section: Concrete |
| Keywords: light transmitting concrete, light transparent concrete, epoxy resin, concrete fines, recycling, mechanical activation, rheology, additive technology |
| Autor: A.S. Pilipenko, S.D. Revyakin. |
The article analyzes the possibilities of using recycled secondary alumino-silicate raw materials in the production of construction materials, the...
| Issue №4, 2024 |
| Section: Application of cement |
| Keywords: secondary raw materials, alumosilicate additive, soil stabilization, waste utilization |
| Autor: V.B. Petropavlovskaya, A.V. Lebedev, K.S. Petropavlovsky, T.B. Novichenkova. |
The effect of shrinkage deformations of cement compositions being reduced when additives, surface tension modifiers, are introduced in the composi...
| Issue №3, 2024 |
| Section: Concrete |
| Keywords: structural concrete, cement mixtures, shrinkage deformation, surface tension, calorimetry, additive compatibility |
| Autor: I.Y. Lavrov, V.A. Beregovoi. |