Journal
The article describes the project undertaken with the direct participation of Cemservice specialists to modernize the closed-circuit cement grindin...
| Issue №2, 2026 |
| Section: Equipment and technology |
| Keywords: grinding, cement, modernization, closed circuit, productivity |
| Autor: A.G. Grinwald, A.N. Sysoev. |
This article examines the potential use of fatty acids as grinding aids for Portland cement clinker. The data are presented on the influence of cer...
| Issue №1, 2026 |
| Section: Science and production |
| Keywords: clinker grinding, grinding aids, fatty acids, fineness, specific surface, mechanical properties. |
| Autor: U.O. Usacheva, A.M. Kovner, M.E. Voronkov. |
Cement grinding is the final and most energyintensive stage in cement production, accounting for 30–40 % of total electrical energy consumption in ...
| Issue №3, 2025 |
| Section: Equipment and technology |
| Keywords: clinker grinding, particle size distribution, cement fineness, grinding aids, artificial intelligence, AI, separator |
| Autor: F. Leitao. |
Competent management of cement grinding is a multi-tasking and controversial process. Until now, there is no clear answer in scientific and techni...
| Issue №2, 2025 |
| Section: Equipment and technology |
| Keywords: particle size distribution, compressive strength, ball mill, vertical roller mill, high-pressure grinding roll |
| Autor: A.S. Dovgalo, N.A. Bedik, E.A. Ivanova, L.N. Levkevich. |
The status and development directions of largecapacity grinding equipment and technology are analyzed. Ball drum mills will remain the grinding mac...
| Issue №1, 2025 |
| Section: Equipment and technology |
| Keywords: ball drum mill, digital modeling, kinetics of grinding bodies movement, lining |
| Autor: V.S. Bogdanov, S.I. Antsiferov, E.A. Sychev, D.V. Bogdanov, I.N. Sukhorukov. |
This paper reviews the system of clinker precrushing with impact-centrifugal mills as an alternative to roller crushers. The method of impact-centr...
| Issue №6, 2024 |
| Section: Equipment and technology |
| Keywords: centrifugal-impact grinding, Portland cement clinker, pre-crushing, particle size distribution, energy saving |
| Autor: M.S. Garkavi, A.V. Artamonov, M.A. Kozin, D.D. Khamidulina, S.A. Nekrasova, E.V. Kolodezhnaya. |
The article considers the need for modeling the modes of operation of ball charges of tube ball mills. The description of the investigated digital ...
| Issue №6, 2024 |
| Section: Equipment and technology |
| Keywords: ball drum mill, grinding bodies, modeling, kinetic energy, potential energy, speed of movement |
| Autor: V.S. Bogdanov, S.I. Antsiferov, E.A. Sychev. |
The possibility of regulating the mode of motion of grinding media by means of a new classifying lining is shown. The regulation of the grinding proce...
| Issue №2 |
| Section: Equipment and technology |
| Keywords: ball drum mill, grinding bodies, lining, mill feed, fineness of grinding, segregation, sorting, energy consumption |
| Autor: V.S. Bogdanov, I.N. Sukhorukov, D.V. Bogdanov, N.P. Nesmeyanov. |
The article presents recommendations of OOO Cemservice related to stage-by-stage upgrading of the cement grinding section and describes the practi...
| Issue №5, 2023 |
| Section: Equipment and technology |
| Keywords: grinding, cement, modernization, closed circuit, productivity, specific power consumption |
| Autor: A.G. Grinvald. |
Production of high quality cement requires information on the mineralogical and chemical composition of the components and the final product. ANTS...
| Issue №5, 2023 |
| Section: Control of production |
| Keywords: sample preparation, equipment, grinding, analysis |
| Autor: I.S. Lisitsyna. |